Make your own plumbing can save you a lot of money, and simple plumbing jobs that do not require extensive knowledge or skills. A beginner should be able to manage simple tasks such as replacing a faucet washer or plumbing in a pool, and a handy way to be able to solve more complex tasks such as plumbing in a shower. But you should think twice before trying to solve very complex tasks. Work on a plumbing system can be dirty work - especially if you have to raise the floor or work in a dusty loft and it can be quite exhausting.
There are two main parts of a plumbing system of the house - a system of water supply and drainage system. The water supply system is a set of pipes and fittings carrying water for baths, sinks, toilets and so on. Waste is another set of pipes that lead away from the wastewater drains and sewers. In an old house or with many plumbing fittings, piping may seem confusing, but basically plumbing systems is very simple. Before the work of starlings on your plumbing system, to follow all the tubes carefully so that you know where each pipe leads and what it does.
Water supply
Hydraulic system basically starts domestic water supply to the company (both water authority or company) with a tap. This is usually located outside the boundary of the real estate of approximately 750 mm from the ground beneath a metal door, probably the sidewalk. Companies need more water stop cocks special wrench to turn them on and off. Tap controls the flow of water between the water in the main water entry and the provision of household water. The pipe that carries water to the faucet in the house known as the service pipe, and the responsibility to keep the house belongs to the owner. Before 1939, the branch pipes were usually made of lead or steel, are now often made of copper or polyethylene. Many of the company taps pipes slope slightly toward the high water at home, but will always be at least 750 mm below ground level.
There are two basic systems to be moving upwards in the water around the house the main places where you wanted it to be direct and indirect.
In piping systems indirect system, the main purpose of the increase primarily to feed water to a cold water tank (often mistakenly referred to as deposit) that is normally found in the attic. Most faucets and other plumbing fixtures in the house will draw water from this reservoir, which remains the band to cut through a ball valve. However, at least one tap usually the knees of cold water in the kitchen should be fed directly from the expansion card to provide drinking water.
According to local water regulations, one, two or more accessories can be made directly access the main - one for a spin out of water and one for cold water for dish washing machine or dishwasher, for example. Another link can be made for an electric shower.
Most of the indirect hot water systems are two pipes (often referred to withdraw the tubes) in water from wells. A feed pipe and cold water taps in bathrooms and other rooms with sinks. More feeds hot water tank, where water is stored and heated by the boiler or electric heater. Tanks for cold water pipes can be pulled in more than a few types of bidet or a shower or make some connections easier.
Hot water taps to get the water from a hose connected to the top of the hot water cylinder - again, the bidet and shower facilities may need their own individual connections. Hot water will also bring a tube in the tank, cold water to provide a safety vent to allow air bubbles and steam to escape.
In order to perform work at a plumbing system or stop a leak or rupture, the different parts of the system should be isolated and drained of water. In theory, a single tap or cock really necessary in a system. This should be as close as possible to the point where the service main pipe enters the house to make it possible for any home to be isolated from the water. Two drain valves are needed - one just above the main drain valve for pipes up primary and secondary connected to it and the other as low as possible to the boiler feed pipe outlet of the cylinder. Feeding tube hot water faucets and valves connected to the cold tank and the tank of cold water itself, can be emptied by turning the taps. It will not drain the hot water tank.
In practice, saving the need to drain the entire system each time the repairs are made, it is better to include more stopvalves, so that in some parts of the HVAC system can be isolated from the rest. This usually means having valves for each draw-off from a well. It can be mounted on a small difference between the valves just prior to every touch, or equipment. There should be a valve in the outlet pipe from the boiler.
Direct Plumbing
In a direct plumbing system, all the cold taps and so on are powered directly through the riser. If hot water is heated by a stock or hot water (rather than hot water) that would normally be powered by a tank of cold water often small on top of the cylinder.
Which system is best
Indirect HVAC system has three important advantages. The first and perhaps most important, because most of the system is disconnected from the grid, a water tank of water is less likely to be pulled back to the grid (this is called back-siphonage), so there is no much less risk of contamination of water supplies. Secondly, the system operates continuously, the water pressure, so you do not have to worry about tap water pressure fluctuations - this is especially important for some of the jets where you need to about the same pressure of hot and cold water . Finally, the tank provides a reservoir of water, if the power fails.
A direct plumbing system is a little less complicated and can be less expensive to install than an indirect effect. But some of the fittings used may need to be specially designed to reduce the risk of contamination of food.
The type of system that allowed the company will be determined by local water supply. The last option is to have a hot water system with no ventilation. In this case, the cold water supply of the house is the system from above, but the cylinder (special) of hot water also is fed directly from the elevator. Unvented hot water systems must be installed and maintained properly, but have several advantages over conventional systems.
Once in the house, the pipe (now called a lift) can be protected from freezing by running along an inside wall. In homes with floor suspension may be necessary to give additional protection for the freezing of the pipe.
There are two main parts of a plumbing system of the house - a system of water supply and drainage system. The water supply system is a set of pipes and fittings carrying water for baths, sinks, toilets and so on. Waste is another set of pipes that lead away from the wastewater drains and sewers. In an old house or with many plumbing fittings, piping may seem confusing, but basically plumbing systems is very simple. Before the work of starlings on your plumbing system, to follow all the tubes carefully so that you know where each pipe leads and what it does.
Water supply
Hydraulic system basically starts domestic water supply to the company (both water authority or company) with a tap. This is usually located outside the boundary of the real estate of approximately 750 mm from the ground beneath a metal door, probably the sidewalk. Companies need more water stop cocks special wrench to turn them on and off. Tap controls the flow of water between the water in the main water entry and the provision of household water. The pipe that carries water to the faucet in the house known as the service pipe, and the responsibility to keep the house belongs to the owner. Before 1939, the branch pipes were usually made of lead or steel, are now often made of copper or polyethylene. Many of the company taps pipes slope slightly toward the high water at home, but will always be at least 750 mm below ground level.
There are two basic systems to be moving upwards in the water around the house the main places where you wanted it to be direct and indirect.
In piping systems indirect system, the main purpose of the increase primarily to feed water to a cold water tank (often mistakenly referred to as deposit) that is normally found in the attic. Most faucets and other plumbing fixtures in the house will draw water from this reservoir, which remains the band to cut through a ball valve. However, at least one tap usually the knees of cold water in the kitchen should be fed directly from the expansion card to provide drinking water.
According to local water regulations, one, two or more accessories can be made directly access the main - one for a spin out of water and one for cold water for dish washing machine or dishwasher, for example. Another link can be made for an electric shower.
Most of the indirect hot water systems are two pipes (often referred to withdraw the tubes) in water from wells. A feed pipe and cold water taps in bathrooms and other rooms with sinks. More feeds hot water tank, where water is stored and heated by the boiler or electric heater. Tanks for cold water pipes can be pulled in more than a few types of bidet or a shower or make some connections easier.
Hot water taps to get the water from a hose connected to the top of the hot water cylinder - again, the bidet and shower facilities may need their own individual connections. Hot water will also bring a tube in the tank, cold water to provide a safety vent to allow air bubbles and steam to escape.
In order to perform work at a plumbing system or stop a leak or rupture, the different parts of the system should be isolated and drained of water. In theory, a single tap or cock really necessary in a system. This should be as close as possible to the point where the service main pipe enters the house to make it possible for any home to be isolated from the water. Two drain valves are needed - one just above the main drain valve for pipes up primary and secondary connected to it and the other as low as possible to the boiler feed pipe outlet of the cylinder. Feeding tube hot water faucets and valves connected to the cold tank and the tank of cold water itself, can be emptied by turning the taps. It will not drain the hot water tank.
In practice, saving the need to drain the entire system each time the repairs are made, it is better to include more stopvalves, so that in some parts of the HVAC system can be isolated from the rest. This usually means having valves for each draw-off from a well. It can be mounted on a small difference between the valves just prior to every touch, or equipment. There should be a valve in the outlet pipe from the boiler.
Direct Plumbing
In a direct plumbing system, all the cold taps and so on are powered directly through the riser. If hot water is heated by a stock or hot water (rather than hot water) that would normally be powered by a tank of cold water often small on top of the cylinder.
Which system is best
Indirect HVAC system has three important advantages. The first and perhaps most important, because most of the system is disconnected from the grid, a water tank of water is less likely to be pulled back to the grid (this is called back-siphonage), so there is no much less risk of contamination of water supplies. Secondly, the system operates continuously, the water pressure, so you do not have to worry about tap water pressure fluctuations - this is especially important for some of the jets where you need to about the same pressure of hot and cold water . Finally, the tank provides a reservoir of water, if the power fails.
A direct plumbing system is a little less complicated and can be less expensive to install than an indirect effect. But some of the fittings used may need to be specially designed to reduce the risk of contamination of food.
The type of system that allowed the company will be determined by local water supply. The last option is to have a hot water system with no ventilation. In this case, the cold water supply of the house is the system from above, but the cylinder (special) of hot water also is fed directly from the elevator. Unvented hot water systems must be installed and maintained properly, but have several advantages over conventional systems.
Once in the house, the pipe (now called a lift) can be protected from freezing by running along an inside wall. In homes with floor suspension may be necessary to give additional protection for the freezing of the pipe.
About the Author:
Learn more about Plumbing Sebastopol . Stop by Leon Burgett's site where you can find out all about Plumbing and what it can do for you.
No comments:
Post a Comment